Tile & Stone Installation
Color Guard Grout Stain
SGM Color Guard Grout Stain is a unique concept in grout and concrete coatings. SGM Color Guard Grout Stain comes available in thirty-two (32) standard SGM colors and is formulated to sink deeply into pores. This coats the aggregate and leaves the coloring below the wearing surface. It dries to a matte finish, maintaining the granular appearance of grout and providing a glare-free, non-skid, uniform color. SGM Color Guard Grout Stain is highly resistant to wear, sunlight, water, and extreme temperature
Product Details
CHARACTERISTICS
- Excellent Workability
- Easy Clean Up
- High Bond Strength
PREPARATION
Surfaces should be in good condition, free from all alkali, moisture, sealers, waxes, dirt or any other foreign materials that would interfere with a good bond. For best results, clean surface with SGM Safe Clean Crystals, followed by a wet scrubbing and flooding with water. Thoroughly, dry surface before application of Color Guard Grout Stain. New grout and concrete surfaces must be thoroughly cured before applying the stain.
- CAUTION: Consult manufacturer of ceramic tile products for compatibility of acid cleaners with their products.
WARNING
Avoid prolonged contact with skin, breathing of dust, vapors, and/or spray mist. Avoid contact with eyes. USE WITH ADEQUATE VENTILATION. Ensure fresh air entry during application and drying. If you experience eye watering, headache, or dizziness, or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH-approved), during and after application. Follow the respirator manufacturer’s directions for respirator use. Use chemical safety glasses, goggles, or a face shield for proper eye protection. Wash thoroughly after handling, and before eating or smoking. KEEP FROM FREEZING. Close container after each use. DO NOT TAKE INTERNALLY. Refer to the Safety Data Sheet (SDS). KEEP OUT OF REACH OF CHILDREN.
APPLICATION
All attempts using Color Guard Grout Stain should be done in an inconspicuous area to test the color compatibility of surface area, application and clean up time. Stir thoroughly and re-mix during application. For grouting applications, apply with a narrow brush using even coats brushing well into the surface. Care should be used in keeping Color Guard Grout Stain off of the tile as much as possible. Narrow grout joints in glazed or porcelain tiles can be applied using a short-napped roller, taking care to clean the tile immediately. If a second coat is necessary, allow thorough drying time between coats. For concrete surfaces apply using a ¾ inch lamb’s wool roller to the entire surface to be stained.
CURING
Surface becomes dry in two (2) to four (4) hours (this will vary with temperature). Wait 24 hours before subjection to foot traffic. Avoid washing for 48 hours.
COVERAGE
- Cement Grout Joints: 300 to 600 sq. ft. per quart depending on joint size.
- Concrete Surfaces: 25 sq. ft. per quart depending on porosity of surface.
CLEAN UP
Wipe up splatters an spills immediately using a cloth dampened with water while still wet.
SHELF LIFE
Up to one (1) year in unopened, properly stored containers.
Available Colors
DISCLAIMER
Sample colors are as accurate as modern technology can produce.
-
Antique -
Almond -
Aztec Gold -
Beach -
Ash -
Champagne -
Charcoal Black -
Canvas -
Burlap -
Buff -
Glacier Blue -
Emerald Ice -
DeLorean Gray -
Dove Gray -
Chocolate -
Créme -
Koala -
Honey -
Khaki -
Light Sand -
Light Buckskin -
Oyster -
Saddle -
Pale Linen -
Natural Gray -
Mocha -
Sunglow -
Sand Dune Beige -
Silver -
White -
Tawny -
Seashell
SGM, Inc. will replace any material proved defective with the maximum shelf life on unused material of up to one (1) year. If our products are not found to conform to our high standards, notify SGM, immediately in writing. There is no other obligation expressed or implied, and we assume no liabilities for damages of any kind. Suitability of the product for an intended use shall be solely up to the user.